[. . . ] PCMCIA is a registered trademarks of the Personal Computer Memory Card International Association. PRISM is a registered trademark of GlobeSpan Virata, Inc. All other products are trademarks or registered trademarks of their respective companies. Warning Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm. Wash hands after handling. Copyright 2004 - Fujitsu Computer Systems Corporation. No part of this publication may be copied, reproduced, or translated, without the prior written consent of Fujitsu Computer Systems Corporation. [. . . ] Radio interference may also occur if the intensity of ambient radio waves is too high. STOPPING TRANSMISSION To use this product inside hospitals, clinics, or airplanes, or in other places where the use of electronic equipment is regulated, stop the transmission of radio waves from the wireless LAN beforehand. Tap PCI-PRISM1, then click File in the toolbar at the top of the screen. Click Disable; wireless communications switching will be deactivated and the transmission of radio waves from the wireless LAN will be stopped. 28 W i r e l e s s L A N U s e r 's G u i d e DISABLING/RE-ENABLING THE WLAN If you do not intend to use the wireless LAN device in your tablet, it is recommended that you disable it. Do not disable the WLAN unless you have no intention of using it. In the process of reenabling it, you will lose any RAM-based data and applications. Disabling the WLAN To disable the wireless LAN device, go to Start -> Programs -> Explorer and double-click on the Windows icon. After executing the file, perform a warm reset of the system by pressing the recessed reset button on the back of the tablet. Re-Enabling the Wireless LAN There are two ways to re-enable the WLAN after having disabled it. Note that both of these methods will result in any RAM-based data and applications being lost. Be sure to back up any data and applications to external media before proceeding. To re-enable the WLAN, the user needs to needs to initialize the system. See "Shutting Down the System" on page 15 for information on performing a cold reset. Open the Fujitsu setup menu by holding the [CLR] button while warm-booting the system (i. e. , pressing the small recessed reset button on the back of the system). Click on [Start] -> Settings -> Network and Dial-up Connections. Tap PCI-PRISM1, then click File in the toolbar at the top of the screen. a. For ad hoc connection: When the "This is a computer-to-computer (ad hoc) network; wireless access points are not used. " box is checked, the Encryption automatically goes to TKIP. For access point (infrastructure) connection: If the access point to be accessed has acquired shared-key authentication, select Shared from the Authentication drop-down menu. 30 W i r e l e s s L A N U s e r 's G u i d e If checked, clear the check mark from the [The key is provided automatically] check box. Enter data in Network key: Depending on the number of entered characters or digits, whether the key is an ASCII character code or a hexadecimal code will be identified automatically. addresses, consult with your network administrator for the correct IP address settings. Processing will return to the [Network and Dial-up Connection] window. Close the [Network and Dial-up Connection] window. Use five or thirteen characters to enter the key in the ASCII character code format. The characters that can be used as the "network key" are as follows: 0 - 9, A - Z, _ (underscore), or, Use 10 or 26 characters to enter the key in the hexadecimal character code format. The characters that can be used as the "network key" in this case are as follows: 0- 9, A - F, a - f For ad hoc connection: Assign the same network key to all the personal computers to be connected. For access point (infrastructure) connection: Assign the identical network key that is programmed into the access point. For this setting, refer to the access point manual or contact your network administrator. Following this operation, confirm the names of the computer and the workgroup as follows. [. . . ] · The files on the device copied using the File manager are not files that are saved together with application programs. FILE MANAGER The CT2000 CE Tablet Explorer enables files to be copied, deleted or the like. Open the Fujitsu setup menu by holding the [CLR] button while warm-booting the system (i. e. , pressing the small recessed reset button on the back of the system). Double-tap the folder name in the file list to switch the list to the contents of that folder. RUN A PROGRAM A file can be executed by specifying its name in setting menu. Open the Fujitsu setup menu by holding the [CLR] button while warm-booting the system (i. e. , pressing the small recessed reset button on the back of the system). 55 Stylistic CT2000 Series CE Tablet User's Guide ­ Appendix 2. [. . . ]